爆炸沸腾研究进展

分析讨论了液体过热极限、汽泡内压力等爆炸沸腾的重要参数 ,综述了三种主要实验方法 ,提出了有待进一步研究的问题 .     

炸药装药在压剪加载下的起爆特点

进行了两类压剪加载实验：（１）利用石英的平面正碰撞产生压剪加载的实验,采用电磁质速法测试装药试件内部不同质点的运动情况,分析炸药装药中发生化学反应的可能性;（２）在压剪炮上采用平行倾斜碰撞产生压剪加载的实验,观测炸药装药爆炸的可能性。由实验可以看出：在亚爆轰状态的压缩加载应力条件下,剪切的联合作用对炸药的起爆起到敏化作用,适当比例的压剪加载造成更加敏感的炸药起爆响应。文中给出了起爆响应规律和响应机制的实验分析。     

计算流体动力学在液体火箭发动机中的应用

对计算流体动力学（ＣＦＤ）在液体火箭发动机中的应用情况进行了全面的回顾与分析,提出了今后的发展趋势与方向。     

模态综合法在求解自行火炮动态特性中的应用

运用自由界面模态综合法将自行地地分为炮身、摇架、高低机、平衡机、炮框、炮塔、车体等子结构.依据频率准则,由有限元法求得各个子结构的分支模态,由整体自由度缩减的动力方程求得全地的动态特性.运用该方法使整体动力方程的阶数大为降低,且保证了求解结果的精度.     

定性测量与定量测量火炸药静电感度的对比分析

采用先进测试系统,对氮化铅、硝化棉、梯恩梯和黑索金火炸药静电感度分别进行了定性测量和定量测量,得出了相对静电感度值和实际静电感度值,并对其进行了对比分析。     

潜射导弹出水过程空化流数值计算

运用Zwart-Gerber-Belamri空化模型,采用动网格和复合网格技术,提出复杂外形潜射导弹出水过程中空化流数值计算方法。对头肩部、舵面及突起物的空化生成、演化及影响因素进行分析。仿真结果表明:出水过程初期空化数降低使附体空泡迅速扩大,随后对空泡脱落与振荡的影响将更为显著;肩部以15 m/s的速度出水时产生空化并随速度上升而迅速增长,5°~10°攻角时肩空化非对称性显现;舵面空化受出水速度影响较小,攻角小于等于5°时空化面积小于全舵面积的10%,但攻角大于5°后空化面积迅速增长至50%以上;减小突起物尺寸有利于避免空化产生,突起物空化受攻角影响较小,但在高速下可诱导临近弹体产生空化。     

爆炸危险环境建筑物防雷设施选择及布置

爆炸危险环境建筑物防雷由于其“特殊性”倍受电气工程技术人员关注。结合相关雷电理论，从接闪器、引下线、接地装置几个方面对爆炸危险环境建筑物防雷设施选择和布置进行了论述。     

滑移边界条件的收敛性分析及应用

用速度滑移与温度跳跃边界条件代替通常假定的无滑移边界条件,可有效地提高计算流体力学模型对高空滑移流区域流动的预测精度。应用Maxwell滑移边界条件时,通过直接计算速度梯度及温度梯度而得到速度滑移和温度跳跃量的处理方法在网格较密的时候会出现迭代计算发散的问题。理论分析表明,直接计算梯度的方法使边界条件的时间推进过程等价于雅克比迭代过程,因此必须满足相应的收敛性条件。为了消除收敛性条件的限制,给出了一种在任意网格密度下均收敛的边界条件处理方法并通过数值算例验证了该方法的正确性。针对高空高超声速流动,以空天飞机为例,对比了滑移/无滑移边界条件所得结果的差异,分析了滑移效应对飞行器气动特性及热环境的影响。     

Novel aluminum-based fuel: Facile preparation to improve thermal reactions

To improve the thermal properties of aluminum (Al) in the energetic system, a coated structure with ammonium perchlorate (AP) was prepared by a facile approach. And N, N-Dimethylformamide (DMF) was chosen as an ideal solvent based on heterogeneous nucleation theory and molecular dynamics simulation. This coated structure could enlarge the contact area and improve the reaction environment to enhance the thermal properties. The addition of AP could accelerate oxidation temperature of Al with around 17.5 °C. And the heat release of 85@15 composition rises to 26.13 kJ/g and the reaction degree is 97.6% with higher peak pressure (254.6 kPa) and rise rate (1.397 MPa/s). An ideal ratio with 15 wt% AP was probed primarily. The high energy laser-induced shockwave experiment was utilized to simulate the reaction behavior in hot field. And the larger activated mixture of coated powder could release more energy to promote the growth of shockwave with higher speed up to 518.7 ± 55.9 m/s. In conclusion, 85@15 composition is expected to be applied in energetic system as a novel metal fuel.     

Prediction of concentration of toxic gases produced by detonation of commercial explosives by thermochemical equilibrium calculations

An adverse effect resulting from explosive mine blasts is the production of toxic nitrogen oxides (NO and NO₂) and carbon monoxide (CO). The empirical measurements of the concentration of toxic gases showed that it depends not only on the composition of an explosive and properties of its ingredients but also on several other parameters, such as volume of blasting chamber, explosive charge mass and design, confinement characteristics, surrounding atmosphere, etc. That explains why measured concentrations of toxic gases reported in literature significantly differ.In this paper, we discuss the possibility of theoretical prediction of the concentration of toxic gases by thermochemical equilibrium calculation applying two models: ideal detonation model and deflagration model. It can be demonstrated that thermochemical calculations can provide a good estimation of the measured concentrations and reproduce experimentally obtained effects of additives on the production of toxic gases. It was also found that the ideal detonation model applies to heavily confined explosive charges, while the deflagration model is more suitable for low detonation velocity explosives with light confinement.